Diagnostic Software for VW-Audi Group Cars

 
881 Sumneytown Pike, Lansdale PA 19446, USA

  Shop  Info  F.A.Q.  Download/Update   Manual  Upgrades  Literature

Loading
Home 
    Products   
        VCDS
            Support
                Online Demo / Manual - Auto Scan Screen

This function scans each controller in the vehicle to retrieve controller information -- Part Numbers, Component number, Soft. Coding, WSC, and Fault codes.

First, you must Select Chassis Type:
There are dozens of different control modules that exist across the entire range of VW/Audi vehicles. No one car has all Modules!  Newer cars have more, older cars have fewer. Because of this, you must select a Chassis Type that contains only those modules that are plausible for a given chassis. There are some exceptions but in general, the Chassis Type is the 7th and 8th digits of the VIN number. For example WAUZZZ4F36N111022 has 7th and 8th digits of 4F and is a "
4F,Audi A6 C6". For additional help determining chassis type, see our Vehicle Application Charts.

If you select Auto Detect (CAN Only) as the Chassis Type on newer cars which have a fully CAN-based diagnostic system, VCDS can automatically determine which modules are installed in a particular car and perform an Auto-Scan of exactly those modules. This can make the Auto-Scan considerably faster.

There is a file in the VCDS directory called AUTOSCAN.TXT, which contains all of the vehicle profiles. It can be edited by simply clicking on the hyperlink above the Chassis Type selection. This will open the file in your default Text editor (like Notepad) to create a custom profile for your vehicle. To help you figure out which controllers are in your car, you can run the Control Module Finder.

The Display Freeze Frame Data checkbox adds Freeze Frame data for Fault Codes on control modules using the KWP-2000 protocols. Note: Not all control modules support this freeze-frame data. As a rule of thumb, cars which were re-designed after 2003 will likely have some control modules which support it, and older designs will not. There's no harm in leaving this enabled in any case. However, un-checking it can make the results less cluttered in a scan which contains many fault codes.

[Start]
This begins the Auto-Scan. Beware; this process can take several minutes.

While the scan is running, VCDS will cycle through the Open Controller and Fault Code screens for each controller before returning to the Auto-Scan screen. On newer control modules which have different Hardware and Software part numbers, Auto-Scan includes the Hardware Part Number as shown in the screenshots..

Once the scan completes, double-clicking on any of the Control Modules highlighted in RED will open the Fault Codes screen for that controller and allow you to clear the codes.
 

[Stop]
This stops the Auto-Scan.
 

[Gateway Installation List]
Only available only on Gateways in cars using a direct CAN connection for diagnostics. This function is also accessible from the Applications Screen. This very fast function takes about 3 seconds to query the car's Gateway to find out what modules are installed in the car and what their status is.   Any modules having fault codes should show a "Malfunction" and will be highlighted in RED.    Modules are directly accessible from this screen by double clicking on the appropriate line.   Changes to the Gateway Installation List can be made using the Gateway Coding function. The following screen-shot is from an Audi A6 (C6/4F):

The Auto-Refresh box can be handy because it can show when a fault code appears in a particular system.

[Clear All DTCs]
This function is only available when using a HEX Interface and is implemented in two ways.   On pre-CAN vehicles, VCDS will access each control module and clear DTCs from each one individually.   On vehicles using CAN for diagnostics, VCDS performs this function without accessing all the control modules individually if  the Use CAN Command box is checked. If you are not using a HEX Interface then you'll need to go into each module that has faults to clear them individually. This function is also accessible from the Applications Screen. The following warning will pop up:

The VIN should be retrieved automatically from all cars which "know" their VIN. Also in control modules that provide it, engine codes and Jxxx component identifiers are shown as well.

Results:

The output from looks like this autoscan-result-A6-11114.txt

If you close the Auto-Scan dialog, any data in its output box will be lost. If you would like to keep a record, click the [Copy] button first, then you can paste the results into the application of your choice, such as MS Word or Notepad.

[Print]
This function sends the results to your printer.

[Save]
This saves your results to a file in your VCDS\Logs directory like this: autoscan-result-A6-11114.txt

[Clear]
This erases your results. This does NOT erase the fault codes from any of the controllers. You'll need to go into each controller to Clear Codes or use the Clear All DTC's function for that.

To return to the Main Screen, click [Close]



Home
    Products
        VCDS
            Support
                Online Demo / Manual -
Output Tests Screen